Renovation is exciting until you find that dust is in everything. You are picking wall tiles, arguing about the benchtop and planning where to place the fridge. In this situation, the last thing that comes to one’s mind is the alarm system, which is the main problem.
Many of the faults in alarm systems we deal with in homes in Sydney come from renovations made six months to two years before. There were no big changes in the house: the sensor was painted over; the wire was cut; the newly installed window was left unexplained. The system seemed to be fine, so everybody believed it was still working well.
Here are five mistakes people make and what should be done instead.
1. Telling your alarm company after the work is done
It is common for people to call to notify about their alarm troubles once the issues are already happening after the builders have left. Instead, one should prevent issues from happening altogether.
If you plan to break walls, make extensions, or move the doors and windows, then the alarm should be consulted beforehand. Wires are often laid inside the walls you are about to demolish, and a technician has the knowledge of the installation behind the walls, telling you what can be disconnected and what can stay in use. Sometimes the problem is no more than moving a keypad, but it can happen that a complete alarm loop needs to be changed, which is definitely cheaper at the knockdown stage than post-demolition repair stage.
It takes only one phone call or visit to save you from the issues in the future. It could also be the right moment to ask whether to replace an old panel or not.
2. Letting trades work around a live system
Tradies are good at their jobs, but alarm gear isn’t something they’re thinking about. A sparky running new power might cut an alarm cable because it looked like leftover wire. A plasterer sands near a motion detector and fills it with fine dust. Someone bumps a door contact out of alignment with a ladder and never mentions it.
Then come the false alarms. A system left armed during works will go off all day, and neighbours stop being sympathetic pretty quickly. Some people just unplug everything, which leaves the house unprotected at the exact time strangers have access and doors are often left open.
Better to have a plan. Ask your installer to isolate the zones affected by the work, cover or remove detectors properly, and keep the rest of the house protected. Tell your builder where the panel and cabling are, and ask them to flag anything they disturb.
3. Painting or plastering over devices
This happens more than you’d think. Detectors, sirens and contacts get painted to match the walls, and a motion sensor with a coat of paint over the lens can’t see properly. Even a thin layer changes how it picks up movement. Door contacts get gummed up too.
Dust is the quieter version of the same problem. Renovation dust is fine, and it gets inside detectors, which can cause random trips or sensors that go quiet when they should be paying attention.
If devices have to come off, have them removed carefully and refitted afterwards, not just wrapped in tape. A technician can clean and check them at the same time. And if something has already been painted, don’t scrape at it yourself. You can easily damage the sensor underneath.
4. Keeping the old sensor layout in a new floor plan
This is the tricky bit. If you’ve knocked through the wall between the kitchen and lounge, the motion sensor that once covered the lounge is now facing a bigger area, and it may not be covering the new parts of the room. Or you may have added a rear extension with a bifold door, and the windows in the extension now not connected to security.
The alarm system is still operational. It still sends a signal, but it doesn’t protect all the relevant areas of the house. This is how blind spots are created, and they often located near new doorways and glass on the ground floor, right at the point expected by an intruder.
When there’s a change in layout, security also must be changed. The installer should check the finished layout, entry points and the coverage area of each zone. If the alarm system is installed in Sydney as part of larger construction, it’s a good idea to involve it already during the design phase.
5. Not testing the system properly afterwards
When the renovation is finally over, everyone’s tired and the house feels like a home again. Nobody wants another job. So the alarm gets armed, the keypad lights up and it’s assumed to be working.
A proper test means walking every zone, triggering every sensor, confirming the siren sounds and the monitoring signal comes through, and checking the battery and backup power. Things get nudged, unplugged and reconnected wrong during building work, and testing is the only way to know.
It’s also a good moment to tidy up access. Did you give a tradie a temporary code? Did anyone borrow a remote or key fob? Change or delete those. User codes made for a plumber months ago have a habit of staying active for years.
Book a service once everything’s finished. Think of it as the final inspection, the same way you’d treat the plumbing or electrical sign-off.
Quick FAQ
Can I leave my alarm on during a renovation? Usually only part of it. The areas where work is happening need to be isolated to avoid constant false alarms, but the rest of the house can and should stay protected. Your installer can set this up.
Should I tell my insurer about the renovation? It’s worth checking your policy. Structural changes can affect your cover, and some insurers ask about security measures, so make sure your alarm matches the finished home.
Conclusion
None of these mistakes are hard to avoid. They just need a bit of thinking ahead. Talk to your alarm company early, protect the system while the trades are in, and test everything at the end. Do that and your new kitchen or extension will be as secure as it looks.